1. Please indicate what on-board preparations you would make for the following (Machinery part),you can simply fill the contents of the survey.
a) Class annual survey:
b) Safety Equipment survey
c) IOPP(including intermediate and renewal survey):
d) SMC intermediate external audit:
e) PSC inspection.
2. What is your spare parts and store management philosophy:
3. What items in the CMS are not accept by ship’s chief engineer and should be surveyed by class surveyor:
4. How to prevent cavitation for the centrifugal pump
5. The purpose of the grounding device of shafting system.
6. What inlet temperature should the F.O and L.O purifier be maintained at, respectively?
7. What is the problem when a boiler is making too much .
a) white smoke:
b) black smoke:
9. Briefly describe the result for a generator engine running on low load for a long period.
10. What is the cause for the “boiling” (too hot) hot well (cascade tank)?
11. What is the cause of the Fresh water generator reduce its capacity?
12. Briefly describe the cause of turbocharger surging.
13. Briefly describe the phenomenon of ignition delay in a diesel engine (also shows in P-T diagram).
14. Describe the starting method for a high starting current electric motor.
15. How to make permanent repair for a holed cross deck (staging is not available) by ship’s crew?
16. If the component of a lube oil purifier are in good condition but the result of lube oil analysis showing the purification efficiency of the purifier is poor, What action you should take?
18. Whether you have experience to overhaul ABB (VTR, RH, RU), MET, NA (NR) turbocharger by yourself?
19. Whether you have confidence to operate Lathe, Arc welder, Gas welder/cutter, Benchworks?
20. How to supervise your first engineer regarding the engine room maintenance work and the leadership?
21. If your crew is unqualified and can not be repatriated timely, how to deal with.
22. List your familiar engine (type)
Main engine:
Generator engine:
Main engine turbocharger:
23. What do you understand as a Planned Maintenance System and how did it work upon your last vessel?
24. What is the acceptable wear rate of the cylinder liner and piston ring for a modern 2-stroke diesel engine?
26．What is your idea for cylinder oil feed rate for a modern 2-stroke diesel engine?
27. When you prepare a repair list for dry docking, if you request to renew a section of steel pipe, what information should be contained?
29. If the heavy fuel oil tank is located adjacent to the forward engine room bulkhead for a bulk carrier, what precaution you should take?
31. Please describe briefly what action you should take when black out.
32. Please describe briefly what action you should take when engine room fire?
35. When the lube oil analysis report shows abnormal, Please describe the cause of abnormal and trouble shooting?
a) High water content for diesel engine:
b) High water content for stern tube system.:
c) Low TBN and higher viscosity for diesel engine:
d) High TBN, high insoluble for diesel engine
e) Low viscosity. Low flash point for trunk piston diesel engine
36. What is your management philosophy for following equipment?
a) Oily bilge separator:
b) Sewage treatment:
c) Incinerator:
37. Please describe briefly how you determine the main engine piston ring condition when regularly inspected through scavenging port.
38. What is the cause of the evaporator heating tube been clogged of Fresh Water Generator?
39. What is the cause of the lubricating oil leaking from main engine or generator engine crankshaft after seal between shaft and engine casing?
40. What is your management philosophy in case of generator engine turbo-charger was out of order?
41. What is the maximum output for the generator engine can run continuously (percentage of the MCR)? If the engine can not reach this load due to high exhaust temperature, which part you should check?
42. Please describe the purpose, function and adjusting of VIT?
43. How to figure out engine output by fuel oil consumption.
44. How to measure the piston ring groove by using slide caliper to measure the height of the ring groove or measure the clearance by filler gauge after install the piston ring in the ring groove. I.e. How deep should insert those tools in the ring groove?
45. Please list out all factors you know which will move the inte***ce between oil and water in a oil purifier to outer edge of the purifier bowl.
a) Class annual survey:
b) Safety Equipment survey
c) IOPP(including intermediate and renewal survey):
d) SMC intermediate external audit:
e) PSC inspection.
2. What is your spare parts and store management philosophy:
3. What items in the CMS are not accept by ship’s chief engineer and should be surveyed by class surveyor:
4. How to prevent cavitation for the centrifugal pump
5. The purpose of the grounding device of shafting system.
6. What inlet temperature should the F.O and L.O purifier be maintained at, respectively?
7. What is the problem when a boiler is making too much .
a) white smoke:
b) black smoke:
9. Briefly describe the result for a generator engine running on low load for a long period.
10. What is the cause for the “boiling” (too hot) hot well (cascade tank)?
11. What is the cause of the Fresh water generator reduce its capacity?
12. Briefly describe the cause of turbocharger surging.
13. Briefly describe the phenomenon of ignition delay in a diesel engine (also shows in P-T diagram).
14. Describe the starting method for a high starting current electric motor.
15. How to make permanent repair for a holed cross deck (staging is not available) by ship’s crew?
16. If the component of a lube oil purifier are in good condition but the result of lube oil analysis showing the purification efficiency of the purifier is poor, What action you should take?
18. Whether you have experience to overhaul ABB (VTR, RH, RU), MET, NA (NR) turbocharger by yourself?
19. Whether you have confidence to operate Lathe, Arc welder, Gas welder/cutter, Benchworks?
20. How to supervise your first engineer regarding the engine room maintenance work and the leadership?
21. If your crew is unqualified and can not be repatriated timely, how to deal with.
22. List your familiar engine (type)
Main engine:
Generator engine:
Main engine turbocharger:
23. What do you understand as a Planned Maintenance System and how did it work upon your last vessel?
24. What is the acceptable wear rate of the cylinder liner and piston ring for a modern 2-stroke diesel engine?
26．What is your idea for cylinder oil feed rate for a modern 2-stroke diesel engine?
27. When you prepare a repair list for dry docking, if you request to renew a section of steel pipe, what information should be contained?
29. If the heavy fuel oil tank is located adjacent to the forward engine room bulkhead for a bulk carrier, what precaution you should take?
31. Please describe briefly what action you should take when black out.
32. Please describe briefly what action you should take when engine room fire?
35. When the lube oil analysis report shows abnormal, Please describe the cause of abnormal and trouble shooting?
a) High water content for diesel engine:
b) High water content for stern tube system.:
c) Low TBN and higher viscosity for diesel engine:
d) High TBN, high insoluble for diesel engine
e) Low viscosity. Low flash point for trunk piston diesel engine
36. What is your management philosophy for following equipment?
a) Oily bilge separator:
b) Sewage treatment:
c) Incinerator:
37. Please describe briefly how you determine the main engine piston ring condition when regularly inspected through scavenging port.
38. What is the cause of the evaporator heating tube been clogged of Fresh Water Generator?
39. What is the cause of the lubricating oil leaking from main engine or generator engine crankshaft after seal between shaft and engine casing?
40. What is your management philosophy in case of generator engine turbo-charger was out of order?
41. What is the maximum output for the generator engine can run continuously (percentage of the MCR)? If the engine can not reach this load due to high exhaust temperature, which part you should check?
42. Please describe the purpose, function and adjusting of VIT?
43. How to figure out engine output by fuel oil consumption.
44. How to measure the piston ring groove by using slide caliper to measure the height of the ring groove or measure the clearance by filler gauge after install the piston ring in the ring groove. I.e. How deep should insert those tools in the ring groove?
45. Please list out all factors you know which will move the inte***ce between oil and water in a oil purifier to outer edge of the purifier bowl.
请登录后评论~
联系我们人工客服
：1391995811
