一．     船体
1．     You must weld and grind this area before painting.
在油漆之前你必须把这个地方电焊修补、打磨好。
2．     This welding line should be gouged and welded again before tightness inspection.
这条焊缝在密性检查前要碳刨、再焊。
3．     The structure of the starboard side is different from the port side.
右舷的结构跟左舷的不一样。
4．     We should reinforce the downside of the windlass.
我们应该在锚机的反面加强。
5．     The navigation deck is not plain, we will fair the deck by hot working.
驾驶甲板不平，我们要火工校正。
6．     There are two pieces of stiffeners and brackets must be replaced.
有两块加强筋和肘板要换新。
7．     Two more footrests and handgrips should be installed at the entrance of the small hatchcover.
在小舱口盖的进口处再安装两只踏步和拉手。
8．     Checking the joint accuracy and structure integrity between No.8 and No.9 block after closed.
No.8 与No9分段合拢后大接头装配精确性和结构完整性检查。
9．     Checking structure integrity of superstructure(deckhouse)after welding.
上层建筑焊后结构完整性检查。
10．     Inspecting fitting accuracy of hatch coaming on board.
货舱口围板船上安装精度检查。
11．     Inspection air pressure test(with water head) for No1. water ballast tank(No15 block).
No1压载水舱（No.15分段）气压试验（压头试验）检查。
12．     Inspection hosing test for upper deck.
上甲板冲水试验检查。
13．     Measuring hull’s main dimensions: length overall(LOA.),length between perpendiculars(LPP.),breath molded(B.),depth molded(D.) and deflection before launching.
下水前测量船体主尺度：总长、两柱间长、型宽、型深、基线挠度。
14．     Inspection distance between draught marks and keel plate after marking out.
划线后检查吃水标尺至平板龙骨之间的距离。
15．     Inspecting fitting accuracy of draught mark(loading line mark).
吃水标志（载重线标志）安装精确性检查。


16．     Inspection welding seam and dimension of cargo hatch cover.
货舱舱口盖焊缝和尺度检查。
二．     轮机
1．     Inspection machining dimension of propeller shaft(intermediate shaft or counter shaft).
螺旋桨轴（中间轴）机加工尺寸检查。
2．     Check for su***ce contact area(metallic contact) between stern shaft and propeller hub tapers. 检查螺旋桨轴与螺旋桨锥度接触面。
3．     Inspection machining dimension of rudder stock.
舵杆机加工尺寸检查。
4．     Inspection rudder carrier after assembly.
上舵承组装后检查。
5．     Inspection machining dimension of rudder pintle.
舵销机加工尺寸检查。
6．     Inspection alignment of stock, rudder blade and pintle.
舵杆、舵叶、舵销连接后中心线检查。
7．     Lowering test and tension test of anchor.
锚投掷试验和拉力试验。
8．     Measuring dimension of shaft coupling bolts and reamer hole.
轴系连接螺栓和钻孔尺寸测量。


9．     Inspection installation correctness of ship’s name plate(funnel mark).
船名牌（烟囱标志）安装正确性检查。
10．     Flexibility and hosing test for small water tight hatch cover(water tight door and window).
水密小舱口盖（水密门、窗）启闭灵活性、冲水检查。
11．     Tightness test(opening and closing test,emergency opening and closing test)for cargo hatch cover.
货舱舱口盖密性试验（启闭试验、应急启闭试验）。
12．     Inspecting anchor throwing away appliance.
弃锚装置检查。
13．     Inspecting centerline positioning for shaft system and rudder system before boring.
轴、舵系镗孔前中心线定位检查。
14．     Optical aligned check for shaft system after boring.
轴系镗孔后光学校中检查。
15．     Hydraulic test for L.O. pipe for stern tube.
艉轴管滑油液压试验。
16．     Measuring diameter of fore and aft stern tube bearing and bushes.
艉轴管前、后轴承与衬套直径测量。

17．     Inspection push-up load for fore and aft stern tube bushes.
艉轴管前、后衬套压入检查。
18．     Measuring clearance between propeller shaft & bearing.
螺旋桨轴与轴承间隙测量。
19．     Flushing L.O.system of stern tube.
艉轴管滑油系统的投油清洗。
20．     Inspecting zero(datum) position of rudder blade.
舵叶0位检查。
21．     Measuring clearance of rudder jumping stopper.
舵止跳块的间隙测量。
22．     Inspecting integrity of steering gear.
操舵装置完整性检查。
23．     Measuring installation clearance of rudder bearing.
舵轴承安装间隙测量。
24．     Flushing of piping system for steering gear.
舵机管路系统的投油清洗。
25．     Mooring test of steering gear.
舵机系泊试验。
26．     Manoeuving test of steering gear during sea trial.
舵机航行中操舵试验。

27．     Emergency manoeuving test of steering gear.
舵机应急操舵试验。
28．     Installation and alignment inspection of windlass.
锚机安装与校中检查。
29．     Anchoring and weighing test of windlass on sea trial.
锚机航行中抛起锚试验。
30．     Adjusting safety device for hydraulic system of steering gear(windlass、mooring winch).
舵机（锚机、绞缆机）液压系统安全装置调整。
31．     Running test and loading test for 4t provision crane.
4吨食物吊运转试验和吊重试验。
32．     Lowering and hoisting test for life boat.
救生艇收放试验。
33．     Loading test of accommodation ladder(pilot ladder).
舷梯（引水员梯）压重试验。
34．     Checking liner of main engine(M.E.).
主机垫片检查。
35．     Tightening inspection for through bolts of main engine(M.E.).